Power-Down Current (IPD)(1,2)

Table 1.
PIC18LF65/66K40 only
Standard Operating Conditions (unless otherwise stated)
Param. No. Sym. Device Characteristics Min. Typ.† Max. +85°C Max. +125°C Units Conditions
VDD Note
D200 IPD IPD Base 0.05 2 9 μA 3.0V  
D201 IPD_WDT Low-Frequency Internal Oscillator/WDT 0.4 3 10 μA 3.0V  
D202 IPD_SOSC Secondary Oscillator (SOSC) 0.6 5 13 μA 3.0V  
D203 IPD_FVR FVR 31 51 60 μA 3.0V FVRCON = 0x81 or 0x84
D204 IPD_BOR Brown-out Reset (BOR) 9 14 18 μA 3.0V  
D205 IPD_LPBOR Low-Power Brown-out Reset (LPBOR) 0.5 3.0 10 μA 3.0V  
D206 IPD_HLVD High/Low Voltage Detect (HLVD) 31 μA 3.0V  
D207 IPD_ADCA ADC - Active 250 μA 3.0V ADC is converting (4)
D208 IPD_CMP Comparator 30 45 48 μA 3.0V  

Data in “Typ.” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.

Note:
  1. 1.The peripheral current is the sum of the base IDD and the additional current consumed when this peripheral is enabled. The peripheral ∆ current can be determined by subtracting the base IDD or IPDcurrent from this limit. Max. values should be used when calculating total current consumption.
  2. 2.The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode with all I/O pins in high-impedance state and tied to VSS.
  3. 3.All peripheral currents listed are on a per-peripheral basis if more than one instance of a peripheral is available.
  4. 4.ADC clock source is FRC.
PIC18F65/66K40 only
Standard Operating Conditions (unless otherwise stated), VREGPM = 1
Param. No. Sym. Device Characteristics Min. Typ.† Max. +85°C Max. +125°C Units Conditions
VDD Note
D250 IPD IPD Base 0.4 4 12 μA 3.0V  

D250A

IPD IPD Base 20 μA 3.0V VREGPM = 0
D251 IPD_WDT Low-Frequency Internal Oscillator/WDT 0.6 5 13 μA 3.0V  
D252 IPD_SOSC Secondary Oscillator (SOSC) 0.8 8.5 15 μA 3.0V  
D253 IPD_FVR FVR 32 53 62 μA 3.0V FVRCON = 0x81 or 0x84
D254 IPD_BOR Brown-out Reset (BOR) 14 19 21 μA 3.0V  
D255 IPD_LPBOR Low-Power Brown-out Reset (LPBOR) 0.7 5.0 13 μA 3.0V  
D256 IPD_HLVD High/Low Voltage Detect (HLVD) 32 μA 3.0V  
D257 IPD_ADCA ADC - Active 280 μA 3.0V ADC is converting (4)
D258 IPD_CMP Comparator 31 47 50 μA 3.0V  

Data in “Typ.” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.

Note:
  1. 1.The peripheral current is the sum of the base IDD and the additional current consumed when this peripheral is enabled. The peripheral ∆ current can be determined by subtracting the base IDD or IPDcurrent from this limit. Max. values should be used when calculating total current consumption.
  2. 2.The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode with all I/O pins in high-impedance state and tied to VSS.
  3. 3.All peripheral currents listed are on a per-peripheral basis if more than one instance of a peripheral is available.
  4. 4.ADC clock source is FRC.