Control A

Name:
CTRLA
Offset:
0x00 [ID-00000fa7]
Reset:
0x00000000
Access:
PAC Write-Protection, Enable-Protected, Write-Synchronized
Bit3130292827262524
DORDCPOLCMODEFORM[3:0]
AccessR/WR/WR/WR/WR/WR/WR/W
Reset0000000
Bit2322212019181716
SAMPA[1:0]RXPO[1:0]TXPO[1:0]
AccessR/WR/WR/WR/WR/WR/W
Reset000000
Bit15141312111098
SAMPR[2:0]IBON
AccessR/WR/WR/WR
Reset0000
Bit76543210
RUNSTDBYMODE[2:0]ENABLESWRST
AccessR/WR/WR/WR/WR/WR/W
Reset000000

Bit 30 – DORD: Data Order

Data Order

This bit selects the data order when a character is shifted out from the Data register.

This bit is not synchronized.

ValueDescription
0 MSB is transmitted first.
1 LSB is transmitted first.

Bit 29 – CPOL: Clock Polarity

Clock Polarity

This bit selects the relationship between data output change and data input sampling in synchronous mode.

This bit is not synchronized.

CPOL TxD Change RxD Sample
0x0 Rising XCK edge Falling XCK edge
0x1 Falling XCK edge Rising XCK edge

Bit 28 – CMODE: Communication Mode

Communication Mode

This bit selects asynchronous or synchronous communication.

This bit is not synchronized.

ValueDescription
0 Asynchronous communication.
1 Synchronous communication.

Bits 27:24 – FORM[3:0]: Frame Format

Frame Format

These bits define the frame format.

These bits are not synchronized.

FORM[3:0] Description
0x0 USART frame
0x1 USART frame with parity
0x2-0x3 Reserved
0x4 Auto-baud - break detection and auto-baud.
0x5 Auto-baud - break detection and auto-baud with parity
0x6-0xF Reserved

Bits 23:22 – SAMPA[1:0]: Sample Adjustment

Sample Adjustment

These bits define the sample adjustment.

These bits are not synchronized.

SAMPA[1:0] 16x Over-sampling (CTRLA.SAMPR=0 or 1) 8x Over-sampling (CTRLA.SAMPR=2 or 3)
0x0 7-8-9 3-4-5
0x1 9-10-11 4-5-6
0x2 11-12-13 5-6-7
0x3 13-14-15 6-7-8

Bits 21:20 – RXPO[1:0]: Receive Data Pinout

Receive Data Pinout

These bits define the receive data (RxD) pin configuration.

These bits are not synchronized.

RXPO[1:0] Name Description
0x0 PAD[0] SERCOM PAD[0] is used for data reception
0x1 PAD[1] SERCOM PAD[1] is used for data reception
0x2 PAD[2] SERCOM PAD[2] is used for data reception
0x3 PAD[3] SERCOM PAD[3] is used for data reception

Bits 17:16 – TXPO[1:0]: Transmit Data Pinout

Transmit Data Pinout

These bits define the transmit data (TxD) and XCK pin configurations.

This bit is not synchronized.

TXPO TxD Pin Location XCK Pin Location (When Applicable) RTS CTS
0x0 SERCOM PAD[0] SERCOM PAD[1] N/A N/A
0x1 SERCOM PAD[2] SERCOM PAD[3] N/A N/A
0x2 SERCOM PAD[0] N/A SERCOM PAD[2] SERCOM PAD[3]
0x3      

Bits 15:13 – SAMPR[2:0]: Sample Rate

Sample Rate

These bits select the sample rate.

These bits are not synchronized.

SAMPR[2:0] Description
0x0 16x over-sampling using arithmetic baud rate generation.
0x1 16x over-sampling using fractional baud rate generation.
0x2 8x over-sampling using arithmetic baud rate generation.
0x3 8x over-sampling using fractional baud rate generation.
0x4 3x over-sampling using arithmetic baud rate generation.
0x5-0x7 Reserved

Bit 8 – IBON: Immediate Buffer Overflow Notification

Immediate Buffer Overflow Notification

This bit controls when the buffer overflow status bit (STATUS.BUFOVF) is asserted when a buffer overflow occurs.

ValueDescription
0 STATUS.BUFOVF is asserted when it occurs in the data stream.
1 STATUS.BUFOVF is asserted immediately upon buffer overflow.

Bit 7 – RUNSTDBY: Run In Standby

Run In Standby

This bit defines the functionality in standby sleep mode.

This bit is not synchronized.

RUNSTDBY External Clock Internal Clock
0x0 External clock is disconnected when ongoing transfer is finished. All reception is dropped. Generic clock is disabled when ongoing transfer is finished. The device can wake up on Receive Start or Transfer Complete interrupt.
0x1 Wake on Receive Start or Receive Complete interrupt. Generic clock is enabled in all sleep modes. Any interrupt can wake up the device.

Bits 4:2 – MODE[2:0]: Operating Mode

Operating Mode

These bits select the USART serial communication interface of the SERCOM.

These bits are not synchronized.

ValueDescription
0x0 USART with external clock
0x1 USART with internal clock

Bit 1 – ENABLE: Enable

Enable

Due to synchronization, there is delay from writing CTRLA.ENABLE until the peripheral is enabled/disabled. The value written to CTRLA.ENABLE will read back immediately and the Enable Synchronization Busy bit in the Synchronization Busy register (SYNCBUSY.ENABLE) will be set. SYNCBUSY.ENABLE is cleared when the operation is complete.

This bit is not enable-protected.

ValueDescription
0 The peripheral is disabled or being disabled.
1 The peripheral is enabled or being enabled.

Bit 0 – SWRST: Software Reset

Software Reset

Writing '0' to this bit has no effect.

Writing '1' to this bit resets all registers in the SERCOM, except DBGCTRL, to their initial state, and the SERCOM will be disabled.

Writing '1' to CTRLA.SWRST will always take precedence, meaning that all other writes in the same write-operation will be discarded. Any register write access during the ongoing reset will result in an APB error. Reading any register will return the reset value of the register.

Due to synchronization, there is a delay from writing CTRLA.SWRST until the reset is complete. CTRLA.SWRST and SYNCBUSY.SWRST will both be cleared when the reset is complete.

This bit is not enable-protected.

ValueDescription
0 There is no reset operation ongoing.
1 The reset operation is ongoing.